Reference · 4 min read
How OTDR distance is calculated
An OTDR measures time, not distance. It sends a pulse of light into the fibre and times the light that comes back, then converts that time into distance with the fibre’s group index (also called IOR, the index of refraction): distance = time × speed of light ÷ group index. A SOR file stores the time of every event, in units of 100 picoseconds, together with the group index, so any viewer can work out the same distances.
The formula
Light travels at 299,792,458 m/s in a vacuum and more slowly in glass. The group index n says how much more slowly: in fibre with a group index of 1.468, light covers about 204,218 km per second, or 20.4 cm per nanosecond.
Distance (m) = travel time (s) × 299,792,458 m/s ÷ n
The instrument measures the time for the light to go out and come back, and halves it. The times stored in a SOR file are already one-way times from the instrument’s front panel, so the viewer does not halve them again.
A worked example
Event 3 of this EXFO MaxTester trace, step by step:
- Stored time183062 × 100 ps = 18306.2 ns
- Group index (IOR)1.46770
- Speed in the fibre299,792,458 m/s ÷ 1.46770 = 204260038 m/s
- Distance18306.2 ns × 204260038 m/s = 3739.2 m
- In the event table3.7392 km
Every distance in the event table, the length of the fibre and the scale of the trace are worked out this way. The trace’s own points are spaced by the sample spacing, 0.319 m in this file, which is the finest distance step the trace can show.
What the group index is
The group index depends on the fibre and the wavelength. For standard single-mode fibre (G.652) it is usually between about 1.467 and 1.468, slightly higher at 1550 nm than at 1310 nm. The exact value is in the fibre or cable maker’s datasheet, and technicians enter it on the OTDR before testing. It is stored in the file’s FxdParams block, multiplied by 100,000, so 1.46800 is stored as 146800.
If a file has no group index, OTDR Wizard uses 1.468 and says so in the Parameters tab.
What a wrong group index does
Distance is inversely proportional to the group index, so an error in the index gives the same relative error in every distance:
| Group index used | Real index | Error | At 10 km |
|---|---|---|---|
| 1.4680 | 1.4700 | +0.14 % | 13.6 m too long |
| 1.4700 | 1.4680 | −0.14 % | 13.6 m too short |
| 1.4650 | 1.4680 | +0.20 % | 20.5 m too long |
A few metres matter when a crew has to dig to a fault. Losses are not affected: the group index changes where an event is shown, not how big it is.
To correct a wrong index, re-analyse the trace on the instrument or in its software with the right value, or multiply each distance by used index ÷ correct index.
Fibre distance is not cable or route distance
The OTDR measures the length of the glass. A cable is shorter than the fibre inside it, because the fibres lie in loose tubes with a helical twist (often 0.5 to 2 % extra length). The route is shorter or longer again, with slack loops at joints, risers and poles. To find a fault on the ground, convert the fibre distance with the cable’s helix factor and add the known slack along the route.
How OTDR Wizard checks the scale
Some files use a time convention that does not match the standard, for example storing round-trip time. If that went unnoticed, every distance would be twice or half the real value. To catch it, the viewer compares the slope of the trace with the fibre attenuation that the OTDR itself stored for each section. When the two agree within a sensible range, the scale is confirmed and the Parameters tab shows the ratio under Distance check. When they differ by a factor of about 2 or ½, the distances are rescaled and a note explains it.
Launch cables and offsets
When a launch cable is used, the instrument can be told its length so that 0 km is the start of the fibre under test, not the instrument’s port. That length is stored as the user offset and shown as Launch offset in the Parameters tab. Event distances are measured from that point; the first part of the trace, inside the launch cable, is drawn at negative distances.