How do I open a SOR file without the OTDR vendor's software?
Drop the file into OTDR Wizard. It reads the file inside your browser, so you don't need EXFO FastReporter, another vendor's desktop tool, or a Windows PC. The trace, the event table and the full parameter list appear in a few seconds.
Which OTDR brands are supported?
Any OTDR that saves the standard Bellcore .sor format, version 2, which current instruments use. Files from EXFO MaxTester 730C, EXFO FTB-4 with FTBx-730C and FTBx-735C modules, Anritsu Access Master, Noyes OFL280 and FiberCloud FC3200 instruments are tested, including files re-saved by EXFO FastReporter. Files from VIAVI, Yokogawa, AFL, Fluke Networks and others follow the same standard. Older version 1 files are not supported yet, and vendor-specific proprietary blocks are kept but not decoded.
How accurate are the distances and losses?
Values are read from the file, not re-measured. Distance is the stored time multiplied by the speed of light and divided by the file's own group index. Each file is also cross-checked: the trace slope must match the fibre attenuation the OTDR itself stored. The cumulative loss in the event table adds the section attenuation and every event loss along the way. It usually lands within a few hundredths of a dB of the end-to-end loss the instrument stored, and the Total loss tile always shows the instrument's own figure.
Can I check traces against pass/fail limits?
Yes. Splices, connectors, reflectance and fibre attenuation are checked against limits you can edit. The defaults are 0.10 dB per splice, 0.50 dB per connector, −35 dB reflectance, and 0.40 dB/km at 1310 nm and 0.30 dB/km at 1550 nm. You can also set a maximum total cumulative loss as your link loss budget. Events that fail are marked in red, with the reason, and the same checks appear in PDF and Excel exports.
Can I compare 1310 nm and 1550 nm traces of the same fibre?
Yes. Files of the same fibre at different wavelengths, such as CORE01_1310.sor and CORE01_1550.sor, are grouped and drawn on top of each other. The All files tab lists every open file with its length, total loss and pass/fail status.
Are my SOR files uploaded to a server?
No. The parser is written in Rust and compiled to WebAssembly, and it runs in your browser tab. Files are read from your disk and never sent over the network. Open files are kept in your browser's own storage so a refresh does not lose them, and Close all removes them. To count free exports, the viewer sends the SHA-256 fingerprint of each exported file and a signature of the device, never the file itself.
Is OTDR Wizard free?
Yes. Viewing, the event table, pass/fail checks, A–B loss markers and the all-files overview are free and unlimited, with no account. Exports to PDF, Excel, CSV and JSON are free for 5 files a month on each device, and free PDF reports carry a small OTDR Wizard note in the footer. After that, extra exports will be available to buy without an account, at Rp 10.000 or US$2 a file with a discount from 4 files, or come with the Pro and Business plans. The SOR editor is in development.
Can I edit a SOR file and save it again?
Not yet. The SOR editor is in development for the Pro and Business plans. The engine underneath already writes valid SOR files, with the map block and checksum recomputed on save. The editor will start with the fields people correct most: cable ID, fibre ID, locations, operator and comments.
Can I export the data?
Yes. Select Export in the viewer to save a PDF test report (one fibre, a 1310/1550 nm pair, or a combined report with a cover page, summary and signature block), an Excel workbook with a sheet per table (summary, events, parameters, trace), CSV tables, or JSON with every value in the file. Exports are made in your browser, like viewing. Each exported file counts as one of your 5 free exports a month.
Does it work on macOS, Linux, tablets and phones?
Yes. It runs in any current version of Chrome, Edge, Firefox or Safari, on desktop or mobile. Nothing is installed.